Wooden Hand Planes: Parts, Adjustment and Restoration

Last reviewed on 2026-10-04

For most of the plane's history every plane was wooden. Metal Bailey planes took over in the late 19th century, but wooden smoothers, jacks, jointers and moulding planes still turn up everywhere, and many woodworkers prefer them: they are light, glide easily, and are simple to repair. Japanese planes are a separate wooden tradition covered in the kanna guide.

Parts of a Wooden Plane

Bedding Angles (Pitch)

NamePitchTypical use
Common pitch45°Most bench planes; general work
York pitch50°Harder woods, smoothing
Middle pitch55°Hard or figured woods; many moulding planes
Half pitch60°Very hard or difficult woods

Higher pitches resist tearout but need more force. The "wear" angle is not a cutting angle; it only controls how freely the shaving clears the throat.

Adjusting with a Hammer

  1. Set the iron: place the iron (and cap iron) on the bed, insert the wedge and press it in by hand.
  2. Advance: tap the top of the iron lightly with a small hammer. Sight down the sole and check the projection.
  3. Lateral: tap the side of the iron near the top to swing the edge.
  4. Lock: tap the wedge lightly to seat it. Seating the wedge can push the iron forward a little, so check again.
  5. Retract or remove: strike the strike button, or the back (heel) of the body on planes without one, while holding the wedge and iron.

It sounds crude, but with a little practice it is quick and precise.

Transitional Planes

From the late 1860s Stanley and others sold "transitional" planes: a wooden body with a cast-iron top carrying a Bailey-style frog, depth adjuster and lever cap. They are adjusted like a metal plane and are usually inexpensive on the used market. Their wooden soles wear and can be trued like any other wooden plane.

Restoring a Wooden Plane

  1. Check the body. Look for cracks through the cheeks or from the mouth, and for woodworm. Small checks at the ends are common and usually harmless.
  2. Clean with a damp rag and mild soap or mineral spirits. Do not soak the plane — wood moves when wet.
  3. Fit the wedge. It should bear evenly along the abutments. A rocking wedge lets the iron move.
  4. True the sole with the iron installed and the wedge set (retracted), so the body is under its working stress. Plane it with a sharp metal plane or rub it on sandpaper on a flat surface; check with a straightedge.
  5. Repair a worn mouth. Truing the sole opens the mouth over time. Glue a hardwood patch into a recess in front of the mouth and cut a new, tighter opening.
  6. Sharpen the iron and restore the cap iron as for a metal plane.
  7. Finish with a light coat of oil (for example boiled linseed oil) on the outside and a little wax on the sole.

Moulding Planes

Moulding planes cut profiles — beads, ogees, coves — using an iron shaped to the profile. Sets of "hollows and rounds" carry stamped size numbers, but the scale varied between makers, so measure the iron rather than trusting the number alone.

Frequently Asked Questions

How do you adjust a wooden hand plane?

With a small hammer: tap the top of the iron to advance it, tap its side for lateral alignment, tap the wedge to lock it, and strike the strike button or heel of the body to retract or release the iron.

What is the difference between bedding angle and wear angle on a wooden plane?

The bedding angle (pitch) is the slope the iron rests on and sets the cutting angle. The wear is the opposite face of the throat; its angle only affects how freely shavings escape.

What wood are wooden planes made from?

Traditionally beech in Europe and America. Some Continental planes have a harder sole glued on, and Japanese planes use Japanese white oak.

How do you restore an old wooden plane?

Clean it without soaking, check for cracks, fit the wedge, true the sole with the iron installed, patch a worn-open mouth if needed, sharpen the iron and finish with a light oil.