Rabbet Planes (and How They Differ from Shoulder Planes)
Last reviewed on 2026-10-04
Quick answer: both have an iron that runs the full width of the body so they can cut into a corner. A rabbet plane is built to cut a rabbet from scratch, usually with a fence, a depth stop and a nicker. A shoulder plane is a precise, low-angle trimming tool with sides ground square to the sole, used to fine-tune tenon shoulders and existing rabbets.
A rabbet (spelled "rebate" in British English) is a step cut along the edge or end of a board — the recess that holds a cabinet back, a glass pane in a door, or the lip of a box lid. Rabbet planes cut that step by hand.
What Makes a Rabbet Plane
- Full-width iron. The cutting edge reaches both sides of the body, so the plane can cut right into the inside corner of the step.
- Fence. Sets the width of the rabbet by riding against the edge of the board.
- Depth stop. Rides on the face of the board and stops the cut at the set depth.
- Nicker (spur). A small blade ahead of the iron that scores the fibres. It is lowered for cross-grain rabbets to stop tearing at the shoulder and raised for work along the grain.
A rabbet plane with a fence is traditionally called a fillister (a "moving fillister" when the fence is adjustable).
Common Rabbet Planes
- Stanley No. 78 — the "duplex" rabbet and fillister plane: cast iron, fence, depth stop, nicker, and a second iron seat at the front for bullnose work. Very common on the used market.
- Record 778 — a heavier rabbet plane with a two-rod fence.
- Wooden moving fillisters and skew rabbets — the traditional wooden versions, often with a skewed iron that pulls the plane into the corner.
- Rabbet block planes — block planes with a full-width iron, handy for trimming rabbets and tenons.
- Bullnose rabbet planes (for example the Stanley No. 75) — the iron sits near the front so they can work close to an obstruction.
Rabbet Plane vs Shoulder Plane
| Rabbet plane | Shoulder plane | |
|---|---|---|
| Main job | Cutting a rabbet from scratch | Trimming shoulders, cheeks and rabbets |
| Iron | Full width; often bevel down at about 45° | Full width; bevel up on a low bed (about 15–18°) |
| Fence and depth stop | Usually yes | Usually no |
| Nicker | Often | No |
| Sides square to sole | Roughly | Precisely (critical for square shoulders) |
| Shaving | Medium to heavy | Very fine |
Many woodworkers cut rabbets with a plow, a saw or a router and own only a shoulder plane for clean-up. If you cut rabbets regularly by hand, a fenced rabbet plane is much faster.
How to Cut a Rabbet with a Rabbet Plane
- Mark the rabbet. Gauge the width on the face and the depth on the edge with a marking gauge.
- Set the fence and depth stop to the gauge lines. Make sure the iron's edge projects a hair past the side of the body on the open side, so the plane cuts a clean wall.
- Set the nicker. Down for cross-grain rabbets, up for rabbets along the grain.
- Start at the far end. Take short strokes at the far end, then start each stroke a little further back until the plane is cutting the full length. This keeps the fence from wandering off the line.
- Keep the plane upright and press the fence firmly against the edge. Tilting it leaves a sloped floor and an undercut wall.
- Finish with full-length strokes until the depth stop rides on the face and the plane stops cutting.
- Clean up the wall and floor with a shoulder plane if needed.
Frequently Asked Questions
What is the difference between a rabbet plane and a shoulder plane?
A rabbet plane is designed to cut rabbets from scratch and usually has a fence, depth stop and nicker. A shoulder plane is a precise low-angle trimming plane with sides ground square to the sole, used to refine tenon shoulders and existing rabbets.
Is a rebate plane the same as a rabbet plane?
Yes. "Rebate" is the usual British spelling; "rabbet" is the usual American spelling. The joint and the tool are the same.
Can a shoulder plane cut a rabbet?
It can, slowly, if you clamp a straight batten on the work as a guide. Without a fence or depth stop it is better suited to trimming a rabbet than cutting one.
What is the nicker on a rabbet plane for?
The nicker (spur) is a small blade that scores the fibres just ahead of the iron when you cut across the grain, so the wall of the rabbet is crisp instead of torn.