Plane Iron Sharpening Angles and Camber
Last reviewed on 2026-10-04
Quick answer: for most bench plane irons (bevel down), grind a 25° primary bevel and hone a micro-bevel of about 30°. On bevel-up planes (block planes, low-angle jacks), the bevel angle adds to the bed angle, so choose it to get the cutting angle you want.
Three Angles to Keep Apart
- Bed angle — the angle of the frog or bed the iron rests on (45° on a standard Bailey bench plane; about 12° or 20° on block planes).
- Bevel angle — the angle you grind and hone on the iron.
- Cutting angle — the angle at which the edge meets the wood. On a bevel-down plane it equals the bed angle; on a bevel-up plane it is bed + bevel.
Angle Chart
| Plane | Bed | Typical bevel | Cutting angle |
|---|---|---|---|
| Bailey bench plane (No. 3–8), bevel down | 45° | 25° ground, 30° honed | 45° (fixed) |
| Low angle block plane | 12° | 25°, honed 30° | 37–42° |
| Standard block plane | 20° | 25°, honed 30° | 45–50° |
| Bevel-up bench / low-angle jack, general | 12° | 25–30° | 37–42° |
| Bevel-up smoother, figured wood | 12° | 38° | 50° |
| Shoulder plane | about 15–18° | 25–30° | about 40–48° |
Why Bevel-Down Irons Stay Near 25–35°
On a bevel-down plane, the bevel faces the wood. The gap between the bevel and the freshly cut surface (the clearance angle) is the bed angle minus the bevel angle: 45° − 30° = 15°. If you hone a bevel-down iron much steeper than about 35°, the clearance shrinks toward zero and the heel of the bevel rubs, so the plane stops cutting. To raise the cutting angle on a bevel-down plane, use a higher-angle frog or a small back bevel instead.
Primary Bevel and Micro-Bevel
Grinding the whole bevel at 25° and honing only a narrow micro-bevel a few degrees steeper makes sharpening quick: each touch-up only polishes a sliver of steel. When the micro-bevel grows to a millimetre or two wide, regrind the 25° primary bevel. Full instructions are in the sharpening guide.
Camber: Shaping the Edge
"Camber" (or "crown") means a slightly curved cutting edge, higher at the corners than in the middle. How much depends on the job:
| Use | Camber |
|---|---|
| Scrub plane | Heavy: roughly 3 in (75 mm) radius on a narrow iron |
| Jack / fore plane for roughing | Strong: about 8–12 in radius |
| Jack for general work, jointer | Slight: a few thousandths of an inch at the corners |
| Smoother | Nearly straight with the corners eased |
| Block, shoulder, rabbet planes | Straight (rabbet and shoulder planes must cut right into the corner) |
How to Camber an Iron
- Heavy camber: shape it on the grinder or a coarse stone, then hone by rolling the iron slightly from side to side as you stroke.
- Slight camber: while honing, put extra finger pressure on one corner for a set number of strokes, then the other corner, then the middle. Repeat on each grit. The corners end up slightly lower.
- Check against a straightedge held to the edge and look for light at the corners.
Does Steel Change the Angle?
Harder, more wear-resistant steels (A2, PM-V11) hold up well at 25–30°. If a micro-bevel chips quickly, raise it by a few degrees. Traditional carbon steel (O1 and vintage Stanley irons) takes a very keen edge at the standard angles.
Frequently Asked Questions
What angle should a plane iron be sharpened at?
For bench planes, a 25° primary bevel with a micro-bevel of about 30°. Bevel-up planes use the same starting point, adjusted up or down to change the cutting angle.
What is the sharpening angle for a low angle block plane?
Usually 25° with a micro-bevel near 30°, giving a 37–42° cutting angle on the 12° bed. Hone steeper (35–38°) for difficult face grain.
What angle does a plane iron sit at in a jack plane?
In a standard Bailey jack plane (No. 5) the iron rests on a 45° frog, bevel down, so it cuts at 45°.
What is the difference between grinding and honing angles?
The grinding angle (primary bevel, usually 25°) shapes most of the bevel. The honing angle (micro-bevel, usually 30°) is a narrow, polished strip at the very edge that does the cutting.
How do you crown or camber a plane iron?
Put extra pressure on each corner in turn while honing so the corners wear back slightly, or grind a curve first for a heavy camber, then hone it.